LAB-SMP (1.2kW to 2.4kW)

LAB-SMS Series 1U Programmable Power Supplies

LAB-SMP (1.2kW to 2.4kW)
Part NumberDescriptionDatasheet Further Information
LAB-SMP 1151.2kW Lab Power Supply 0 - 15V, 0 - 80A outputClick for datasheetEnquire Here0
LAB-SMP 1351.2kW Lab Power Supply 0 - 35V, 0 - 35A outputClick for datasheetEnquire Here0
LAB-SMP 1451.2kW Lab Power Supply 0 - 45V, 0 - 30A outputClick for datasheetEnquire Here0
LAB-SMP 1701.2kW Lab Power Supply 0 - 70V, 0 - 20A outputClick for datasheetEnquire Here0
LAB-SMP 11501.2kW Lab Power Supply 0 - 150V, 0 - 8A outputClick for datasheetEnquire Here0
LAB-SMP 13001.2kW Lab Power Supply 0 - 300V, 0 - 4A outputClick for datasheetEnquire Here0
LAB-SMP 16001.2kW Lab Power Supply 0 - 600V, 0 - 2A outputClick for datasheetEnquire Here0
LAB-SMP 112001.2W Lab Power Supply 0 - 1200V, 0 - 1A outputClick for datasheetEnquire Here0
LAB-SMP 2352.4W Lab Power Supply 0 - 35V, 0 - 68A outputClick for datasheetEnquire Here0
LAB-SMP 2452.4W Lab Power Supply 0 - 45V, 0 - 53A outputClick for datasheetEnquire Here0
LAB-SMP 2702.4W Lab Power Supply 0 - 70V, 0 - 34A outputClick for datasheetEnquire Here0
LAB-SMP 21502.4W Lab Power Supply 0 - 150V, 0 - 16A outputClick for datasheetEnquire Here0
LAB-SMP 23002.4W Lab Power Supply 0 - 300V, 0 - 8A outputClick for datasheetEnquire Here0
LAB-SMP 26002.4W Lab Power Supply 0 - 600V, 0 - 4A outputClick for datasheetEnquire Here0

Product Summary

The LAB-SMP series of laboratory DC Sources provides power outputs up to 2.4kW. A wide array of voltage and current ranges are
available at each power rating. Constant voltage, power, resistance and current operating modes are provided as standard. The LAB-SMP
also allows the voltage and current outputs to be preset and read before applying them to the load. To enable remote control a number of
optional analogue and/or computer interfaces can be specified. The optional SD card can further provide a low cost method of recording
and implementing complex waveforms. These PSUs are found in a wide variety of fields from automotive applications and general lab
work to battery charging and automatic test systems. The PV mode allows for basic simulation of a solar cell array via adjustable I and V
values. Your chosen unit is built with a systems interface for master/slave operation. This enables setting values to be equally shared
amongst units that are configured in parallel. The LAB-SMP design is exceptionally flexible and allows CP Power to offer variety of solutions to your particular application requirements.

Please contact our office if you require any changes from the standard specification or any specific modifications.
A soft interlock circuit allows users to connect the unit to an external safety device such as an
emergency stop. This feature requires a high signal (+10V) to be present between two pins, otherwise the output will be shutdown

To find the unit most suited to your requirements simply look in the model table above, or view the pdf data sheet

If you would like to discuss your application in more detail please call us on +44 (0) 2476 214799 or fill out and submit the form on the left of this page.